Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
Everybody has got their own unique views on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably difficult task. If the old tub is conveniently accessible, the task can move speedily; if you have to open a wall surface to remove the old tub and also place the brand-new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have qualified on your own for the work and also fit attempting it. Instead of employing a service provider to take control of a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your bathroom if you have actually already gotten a new bathtub and do not need to transform the arrangement of your previous water pipes.
Your devices and material list should make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the restricted gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up taps, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the supply of water and check all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been used a minimum of when as this will settle it into its final placement.
Preparing for the Installment
To start with, the sustaining frame supplied with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, causing issues with dampness and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealer can crack rather very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about Installing A Bathtub, I assumed sharing that blog post was a smart idea. If you enjoyed reading our blog entry plz don't forget to share it. We treasure reading our article about Tools You Need to Install a New Bathtub .
Sink issues? Expert consultation here. Report this page